Juniper Mist Monitoring and Analytics · Topic 1 of 3

Service Level Expectations (SLEs)

Learn Juniper Mist SLEs: success rate, thresholds, classifiers and sub-classifiers, the SLE block, Settings and the root cause analysis page for the exam.

  • 5 min
  • Includes a diagram
In a nutshell
  • SLEs are at Monitor > Service Levels, with Wireless, Wired, WAN, Location and Insights buttons.
  • Success rate is the percentage of user experiences that met the threshold.
  • Each SLE block shows the overall service level, a timeline and the classifiers.

What it is

Service Level Expectations (SLEs) are the metrics Juniper Mist uses to represent each user's network experience. You set a success threshold, Mist counts how many user experiences met it, and for every experience that failed it identifies the most likely cause.

SLEs are both a health score and a troubleshooting tool. You start at the SLE, click the classifier that holds most of the failures, and drill down to the affected APs, switches, WAN edges or clients.

User experiencecompared withThresholdmetSuccessThresholdmissedClassifierroot causedrill downAffected items

How it works

Where to find SLEs

Select Monitor > Service Levels from the left menu. Buttons at the top switch between the Wireless, Wired, WAN, Location and Insights dashboards. Your subscriptions decide which buttons appear.

At the top you also choose the context, such as the entire organization, a site, an AP or a client, and the time period. The page shows data from the past 60 minutes up to the last 7 days. A Premium Analytics subscription extends wireless history to up to 3 years.

Success rate and user minutes

Each SLE shows a success rate, the percentage of user experiences that met the threshold. If Time to Connect shows 74 percent, 74 percent of connection attempts were fast enough and 26 percent were not.

Many SLEs are measured in user minutes: each minute a user is connected is marked as meeting or missing the threshold. Coverage, for example, counts user minutes where the signal was below the RSSI threshold. Connection SLEs count attempts instead.

The SLE block

An SLE block shows the overall service level on the left, the timeline in the middle and the classifiers on the right. The classifiers split 100 percent of the failures, and sub-classifiers narrow the cause further. Each SLE has a block with three parts.

PartPositionShows
Overall service levelLeftThe success rate for the selected context and time
TimelineMiddleHow the SLE changed over the time period
ClassifiersRightHow the failures split between causes

Every failed experience is assigned to exactly one classifier, so the classifiers always add up to 100 percent of the failures. Many classifiers have sub-classifiers that narrow the cause further.

SLEsuccess ratefailures split intoClassifiers100 percentnarrowed bySub classifiers

Example classifiers

SLEClassifiers
Successful Connects (wireless)Association, Authorization, DHCP, ARP, DNS
CoverageWeak Signal, Asymmetry Downlink, Asymmetry Uplink
RoamingLatency, Stability, Signal Quality
Throughput (wireless)Network Issues, Coverage, Device Capability, Capacity
CapacityNon-Wi-Fi Interference, Client Usage, Wi-Fi Interference, Client Count
AP HealthLow Power, AP Disconnected, Ethernet, Network
Switch Health (wired)Switch Unreachable, Capacity, Network, System
WAN Link HealthNetwork, Interface

Sub-classifiers make the cause concrete. The wireless DHCP classifier splits into Renew Unresponsive, Nack, Incomplete and Discover Unresponsive. The Roaming Signal Quality classifier includes Sticky Client, Suboptimal Roam and Interband Roam.

Thresholds

Click Settings on the SLE dashboard to open the Customize Service Levels window. Some thresholds can be changed and some cannot.

SLEThreshold
Time to ConnectConfigurable time in seconds
CoverageConfigurable RSSI value
ThroughputConfigurable speed in Mbps
CapacityConfigurable share of channel capacity
Successful Connects (wireless and wired)Not configurable
RoamingNot configurable; a roam quality score of 2 on a 1 to 5 scale
Exam tip

Changing a threshold changes the success rate you see, not the network. Set thresholds that match what your users actually need, then use the classifiers to find what is pulling the score down.

Root cause analysis page

Click any SLE or classifier to open its root cause analysis page. The top shows all classifiers and sub-classifiers with their share of failures. The lower section gives details such as statistics, a timeline, the distribution of failures and the Affected Items list, which you can filter to find a particular AP, switch or client.

The distribution view is often the fastest clue. If most failures sit on one AP, one WLAN or one device type, the problem is local; if they spread evenly, look at a shared service such as DHCP or RADIUS.

Common mistakes

Reading the classifier percentages as a share of all users. Classifiers split only the failures. A classifier at 80 percent with a 98 percent success rate means 80 percent of the 2 percent that failed.

Expecting every threshold to be adjustable. Successful Connects and Roaming thresholds cannot be changed.

Confusing Time to Connect with Successful Connects. Time to Connect counts clients that connected too slowly; Successful Connects counts attempts that failed.

Watch out

Each failed experience goes to one classifier only. An option claiming a single failure is counted under two classifiers is wrong.

What to remember for the exam

  • SLEs are at Monitor > Service Levels, with Wireless, Wired, WAN, Location and Insights buttons.
  • Success rate is the percentage of user experiences that met the threshold.
  • Each SLE block shows the overall service level, a timeline and the classifiers.
  • Each failure is assigned to one classifier; classifiers total 100 percent of failures.
  • Sub-classifiers narrow a classifier further, such as DHCP into Nack or Discover Unresponsive.
  • Thresholds are changed with Settings in the Customize Service Levels window.
  • Successful Connects and Roaming thresholds are not configurable.
  • The root cause analysis page lists affected items you can filter.
  • Default history is up to 7 days; Premium Analytics extends it.

Check yourself

  • The Coverage SLE is at 90 percent and Weak Signal holds 70 percent. What does 70 percent refer to?

    It is the share of the failing user minutes, the 10 percent that missed the threshold, that were caused by weak signal.

  • Where do you change the Time to Connect threshold?

    Click Settings on the SLE dashboard to open the Customize Service Levels window.

  • Can you change the threshold of the Successful Connects SLE?

    No. The Successful Connects threshold is not configurable.

Topic 1 of 3 in Juniper Mist Monitoring and Analytics

Test yourself on Juniper Mist Monitoring and Analytics

The full Juniper JNCIA-MistAI JN0-253 question bank has 668 questions, with timed practice exams and an explanation for every answer.

This study guide is independent and is not affiliated with, endorsed by, or sponsored by Juniper. Vendor names, certification names and exam codes are trademarks of their respective owners and are used for identification only.