Networking Fundamentals · Topic 1 of 5

Ethernet and Layer 2 Addressing

Learn Ethernet frames, MAC address format, unicast, multicast and broadcast, and address resolution with ARP and IPv6 neighbor discovery for JN0-106.

  • 5 min
In a nutshell
  • A MAC address is 48 bits; the first 24 bits are the OUI.
  • Broadcast MAC is ff:ff:ff:ff:ff:ff; a 1 in the lowest bit of the first byte means multicast.
  • Ethernet payload is 46 to 1500 bytes; a standard untagged frame is 64 to 1518 bytes.

What it is

Ethernet is the Layer 2 technology used on almost every wired LAN. It defines the frame format, the MAC addresses that identify interfaces on a segment, and how devices share or use the link.

Layer 2 addressing means the MAC address. A frame is delivered on the local segment by MAC address, while the IP packet inside it carries the end to end Layer 3 addresses. Address resolution finds the MAC address that belongs to a known IP address on the same segment: ARP does this for IPv4 and neighbor discovery does it for IPv6.

Host knowsnext hop IPARP request broadcastAll hostson segmentARP reply unicastHost learnsMAC addressFrame sentto that MAC

How it works

The Ethernet frame

FieldSizePurpose
Preamble and SFD8 bytesSynchronizes the receiver; not counted in the frame size
Destination MAC6 bytesWho the frame is for
Source MAC6 bytesWho sent it
EtherType or Length2 bytesPayload type, for example 0x0800 IPv4, 0x86DD IPv6, 0x0806 ARP
Payload46 to 1500 bytesThe packet, padded if shorter than 46 bytes
FCS4 bytesCRC to detect damaged frames

A standard frame is 64 to 1518 bytes without a VLAN tag. An 802.1Q tag adds 4 bytes. A receiver that finds a bad FCS drops the frame; Ethernet itself does not resend it, so recovery is left to upper layers such as TCP.

Half and full duplex

Early Ethernet shared one medium, so stations used CSMA/CD: listen before sending, detect collisions, back off and retry. Modern switched links are full duplex, where each side sends and receives at the same time and collisions cannot happen. A duplex mismatch, one side full and the other half, shows up as late collisions and errors on the interface.

The MAC address

A MAC address is 48 bits, written as 12 hexadecimal digits. Junos OS shows it with colons, for example 00:05:86:71:1a:c0.

PartBitsMeaning
OUIFirst 24 bitsOrganizationally unique identifier, assigned to the vendor
Device partLast 24 bitsAssigned by the vendor to the interface

The lowest bit of the first byte is the individual/group bit. If it is 0 the address is unicast; if it is 1 the address is multicast. The broadcast address is all ones, ff:ff:ff:ff:ff:ff, and every station on the segment processes it.

ARP for IPv4

Before a host sends an IPv4 packet on Ethernet it needs the MAC address of the next hop. If the destination is on the same subnet, the next hop is the destination itself; if not, it is the default gateway.

  1. The host checks its ARP cache.
  2. If there is no entry, it broadcasts an ARP request: "Who has 10.1.1.1?"
  3. The owner of 10.1.1.1 sends a unicast ARP reply with its MAC address.
  4. The host caches the mapping and sends the frame.

On a Junos device, show arp lists the IPv4 to MAC mappings it has learned, with the interface for each entry.

user@router> show arp no-resolve
MAC Address       Address         Interface     Flags
00:05:86:71:1a:c0 10.1.1.2        ge-0/0/1.0    none

no-resolve stops the device from trying to turn the IP addresses into host names, which makes the output faster.

Neighbor discovery for IPv6

IPv6 has no broadcast and no ARP. Neighbor Discovery Protocol (NDP) uses ICMPv6 messages instead.

ARP (IPv4)NDP (IPv6)
ARP request, sent as broadcastNeighbor solicitation, sent to a solicited-node multicast address
ARP replyNeighbor advertisement
ARP cache, show arpNeighbor cache, show ipv6 neighbors
Own protocol, EtherType 0x0806Part of ICMPv6, carried inside IPv6

NDP also handles router discovery, so a host can learn its default router and prefix from router advertisements.

IPv6 hostneighbor solicitationSolicited nodemulticast groupneighbor advertisementIPv6 hostcaches MAC

Where the MAC address changes

As a packet crosses routers, the IP addresses stay the same end to end, but the MAC addresses change on every hop. Each router strips the incoming frame, looks up the destination IP, resolves the next hop MAC and builds a new frame.

PC Aframe to router MACRouternew framePC Bframe to PC B MAC

Common mistakes

Thinking the destination MAC is the remote host. When the destination is on another subnet, the frame goes to the default gateway's MAC address, not the remote host's. The host ARPs for the gateway.

Expecting ARP in IPv6. IPv6 uses neighbor solicitation and neighbor advertisement over ICMPv6, and there is no broadcast at all.

Mixing up the MAC address halves. The vendor part is the first 24 bits (OUI), and the vendor assigned serial is the last 24 bits.

Watch out

An ARP request is a broadcast, but the ARP reply is unicast. Exam options often swap the two.

What to remember for the exam

  • A MAC address is 48 bits; the first 24 bits are the OUI.
  • Broadcast MAC is ff:ff:ff:ff:ff:ff; a 1 in the lowest bit of the first byte means multicast.
  • Ethernet payload is 46 to 1500 bytes; a standard untagged frame is 64 to 1518 bytes.
  • The FCS detects errors; damaged frames are dropped, not repaired.
  • ARP maps IPv4 to MAC; request is broadcast, reply is unicast; view it with show arp.
  • IPv6 uses NDP (ICMPv6 neighbor solicitation and advertisement); view it with show ipv6 neighbors.
  • MAC addresses change hop by hop; IP addresses do not.

Check yourself

  • A host sends a packet to a server in another subnet. Which MAC address is the frame's destination?

    The default gateway's MAC address, because frames are delivered only on the local segment.

  • Which IPv6 messages replace the ARP request and ARP reply?

    Neighbor solicitation replaces the request and neighbor advertisement replaces the reply, both carried in ICMPv6.

  • How many bits is a MAC address, and which part identifies the vendor?

    48 bits; the first 24 bits are the OUI that identifies the vendor.

Topic 1 of 5 in Networking Fundamentals

Test yourself on Networking Fundamentals

The full Juniper JNCIA-Junos JN0-106 question bank has 1,155 questions, with timed practice exams and an explanation for every answer.

This study guide is independent and is not affiliated with, endorsed by, or sponsored by Juniper. Vendor names, certification names and exam codes are trademarks of their respective owners and are used for identification only.