OSPF · Topic 1 of 5

Link State Database, Packet Types and Router ID

Learn the OSPF link state database, the five OSPF packet types, SPF calculation and how Junos chooses and sets the OSPF router ID for the JN0-352 exam.

  • 5 min
In a nutshell
  • Routers flood LSAs, store them in the LSDB, then run SPF.
  • All routers in one area hold an identical LSDB.
  • Packet types: 1 Hello, 2 DBD, 3 LSR, 4 LSU, 5 LSAck.

What it is

OSPF is a link state protocol. Every router describes its own links in messages called link state advertisements (LSAs), and floods them to all routers in the area. Each router stores what it receives in the link state database (LSDB).

All routers in one area end up with an identical LSDB. Each router then runs the shortest path first (SPF) algorithm on that database, with itself as the root, and installs the best routes in the routing table.

The router ID is the 32-bit number, written like an IPv4 address, that identifies a router in the LSDB and in every OSPF packet it sends.

Routeroriginates LSAsfloodingAll routers in areastoreIdentical LSDBSPF runShortest path treebest routesRouting table

How it works

The link state database

The LSDB holds one LSA per advertising router and per link or prefix. An LSA is identified by its type, its link state ID and the advertising router. It also carries a sequence number and an age.

  • A higher sequence number is a newer LSA.
  • The originating router refreshes its LSAs before they expire, with a new sequence number. The standard refresh time is 30 minutes; Junos uses 50 minutes by default (lsa-refresh-interval).
  • An LSA reaching an age of 60 minutes (MaxAge) is removed from the database.

When the topology changes, the router that sees the change floods a new LSA, and every router in the area re-runs SPF.

user@router> show ospf database

    OSPF database, Area 0.0.0.0
 Type       ID               Adv Rtr           Seq      Age  Opt  Cksum  Len
Router   *10.255.0.1       10.255.0.1       0x80000007   212  0x22 0x4a1c  60
Router    10.255.0.2       10.255.0.2       0x80000005   198  0x22 0x7e21  60
Network   10.1.1.2         10.255.0.2       0x80000002   198  0x22 0x91d0  32

The asterisk marks an LSA the local router originated. Add extensive for the full content, or a type (router, network, netsummary, asbrsummary, external, nssa) to filter. The LSDB is kept per area, so each area gets its own section.

The five OSPF packet types

OSPF runs directly over IP as protocol 89. It does not use TCP or UDP. OSPFv2 sends to the multicast address 224.0.0.5 (all OSPF routers) and, for the designated router, 224.0.0.6.

TypeNamePurpose
1HelloDiscover neighbors, check parameters, keep adjacencies alive, elect the DR and BDR
2Database description (DBD)Summarize the contents of the LSDB when an adjacency forms
3Link state request (LSR)Ask for a full LSA the router is missing or has an old copy of
4Link state update (LSU)Carry full LSAs, used in flooding and in answers to requests
5Link state acknowledgment (LSAck)Confirm receipt of LSAs, which makes flooding reliable
Hellotype 1neighbor seenDBDtype 2missing LSA foundLSRtype 3answered byLSUtype 4confirmed byLSAcktype 5

Hello packets carry values that must match for a neighbor to be accepted. These are the area ID, the hello and dead intervals, the authentication type and key, the subnet mask on broadcast links and the stub area flag. Junos defaults are a hello interval of 10 seconds and a dead interval of 40 seconds.

The router ID

Every OSPF router must have a unique router ID. Junos OS takes it from the first address it finds, which is normally the loopback address, unless you set it. Do not rely on that, because adding an interface address can change the router ID after a restart of the process.

Configure it explicitly under routing-options, because it is shared with other protocols such as BGP:

user@router# set routing-options router-id 10.255.0.1
FactDetail
Format32 bits, written in dotted decimal
Must be uniqueDuplicate router IDs in an area cause LSA conflicts and unstable routing
Must it be a reachable addressNo, but using the loopback address is good practice
After you change itThe OSPF adjacencies are reset to use the new ID
OSPFv3Still a 32-bit ID; configure it, because an IPv6 only router has no IPv4 address to take it from
user@router> show ospf overview
Instance: master
  Router ID: 10.255.0.1
  Route table index: 0
  Area: 0.0.0.0
    Stub type: Not Stub
    Authentication Type: None
    Area border routers: 0, AS boundary routers: 0

show ospf overview shows the router ID, the areas and their stub type and authentication.

Exam tip

When two routers appear as one in the LSDB, or an LSA keeps being replaced, suspect duplicate router IDs. Check show ospf overview on both routers.

Common mistakes

Letting Junos pick the router ID. It may change when interface addresses change. Set routing-options router-id and keep it stable.

Believing OSPF uses TCP or UDP. It is IP protocol 89, so a firewall filter must match protocol ospf.

Comparing an LSA's age with the refresh time. LSAs are refreshed before they reach 60 minutes (every 30 minutes in the standard, 50 minutes by default in Junos) and expire at 60 minutes.

Reading the LSDB as one table for the whole network. There is one LSDB per area, plus the AS wide external LSAs.

Watch out

A firewall filter on lo0.0 that does not accept OSPF will stop adjacencies from forming. OSPF packets to the router are local traffic, so the loopback filter sees them.

What to remember for the exam

  • Routers flood LSAs, store them in the LSDB, then run SPF.
  • All routers in one area hold an identical LSDB.
  • Packet types: 1 Hello, 2 DBD, 3 LSR, 4 LSU, 5 LSAck.
  • OSPF is IP protocol 89, multicast 224.0.0.5 and 224.0.0.6.
  • Junos default hello 10 seconds, dead 40 seconds.
  • LSAs age out at 60 minutes (MaxAge); they are refreshed before that, every 50 minutes by default in Junos.
  • Set the router ID with routing-options router-id; it must be unique.
  • show ospf database, show ospf overview and show ospf neighbor are the first commands.

Check yourself

  • Which OSPF packet type carries the full LSAs?

    The link state update (type 4), which is used for flooding and for answering link state requests.

  • What are the Junos default hello and dead intervals?

    Hello 10 seconds and dead 40 seconds.

  • Why should you configure the router ID explicitly?

    Without it Junos picks an interface address, which may change, and a changed router ID resets the adjacencies and can create duplicates.

Topic 1 of 5 in OSPF

Test yourself on OSPF

The full Juniper JNCIS-ENT JN0-352 question bank has 846 questions, with timed practice exams and an explanation for every answer.

This study guide is independent and is not affiliated with, endorsed by, or sponsored by Juniper. Vendor names, certification names and exam codes are trademarks of their respective owners and are used for identification only.