Layer 2 Security · Topic 1 of 4

BPDU, Loop and Root Protection

Learn Junos BPDU protection, root protection and loop protection: what each prevents, the bpdu-block-on-edge, no-root-port and loop-protect statements.

  • 5 min
In a nutshell
  • BPDU protection: edge ports that receive a BPDU are disabled; bpdu-block-on-edge.
  • disable-timeout under protocols layer2-control bpdu-block brings the port back automatically.
  • Root protection: no-root-port; superior BPDU leaves the port in a root inconsistent state, and it recovers by itself.

What it is

Spanning tree trusts every BPDU it receives. That trust is a risk on access ports and on links to other parties. Three Junos features protect the tree.

  • BPDU protection shuts down an edge port that receives a BPDU. A host port should never receive one.
  • Root protection stops a port from becoming the root port. It keeps a switch you do not control from taking over the root bridge role.
  • Loop protection guards a port that expects BPDUs against the loss of those BPDUs, which could otherwise open a loop.
Edge port receives BPDUBPDU protectionport disabledSuperior BPDU receivedRoot protectionport blockedBPDUs stop arrivingLoop protectionport blocked

How it works

BPDU protection

An edge port connects to a host and goes to forwarding at once. If someone plugs in a switch, that switch may send BPDUs and even claim to be root. BPDU protection puts the port out of service the moment a BPDU arrives.

user@switch# set protocols rstp interface ge-0/0/5 edge
user@switch# set protocols rstp bpdu-block-on-edge

bpdu-block-on-edge applies to all edge ports of the RSTP instance. A port blocked this way stays down until you re-enable it with clear error bpdu interface ge-0/0/5, or until an automatic recovery time ends if you set one.

user@switch# set protocols layer2-control bpdu-block disable-timeout 120

With this timer, a blocked port returns to service after 120 seconds. If a BPDU keeps arriving, it blocks again.

Root protection

Root protection is for ports that must never lead toward the root bridge, such as ports toward customers or toward switches outside your control. The statement is no-root-port.

user@switch# set protocols rstp interface ge-0/0/10 no-root-port

If a superior BPDU, one that would make the neighbor root, arrives on that port, the switch does not accept it. The port is put into a root inconsistent state and does not forward, but it keeps listening. When the superior BPDUs stop, the port recovers on its own.

Loop protection

Loop protection is for ports that receive BPDUs and should keep receiving them: root ports and alternate ports. If BPDUs stop, perhaps because of a one way link failure or a faulty neighbor, a blocked port would normally move to forwarding as designated. That could create a loop.

user@switch# set protocols rstp interface ge-0/0/23 bpdu-timeout-action block

With loop protection, the port goes to a loop inconsistent state and stays blocked when BPDUs stop. When BPDUs arrive again, the port recovers on its own. The other action, alarm, only logs the event and does not block the port.

Comparing the three

BPDU protectionRoot protectionLoop protection
Applies toEdge portsDesignated ports facing outsidersRoot and alternate ports
TriggerAny BPDU receivedSuperior BPDU receivedBPDUs stop arriving
ResultPort disabledPort blocked, root inconsistentPort blocked, loop inconsistent
RecoveryManual, or disable-timeoutAutomatic when superior BPDUs stopAutomatic when BPDUs resume
Statementbpdu-block-on-edgeno-root-portbpdu-timeout-action block
Edge porthost sideBPDU protectionDesignated porttoward outsideRoot protectionRoot or alternate porttoward coreLoop protection

Monitoring

user@switch> show spanning-tree interface
user@switch> show spanning-tree bridge
user@switch> show interfaces terse ge-0/0/5

show spanning-tree interface lists the port state, and a protected port that has triggered shows the inconsistent or blocked condition instead of forwarding. show interfaces terse shows whether BPDU protection has taken the port down. The system log records the event, which you read with show log messages.

Exam tip

Combine the features by position. Edge ports get edge with BPDU protection. Ports toward outsiders get no-root-port. Uplinks toward the core get loop protection.

Watch out

Root protection is not the same as making the switch the root. It only refuses a better root on that port. To pick the root, lower the bridge priority.

Common mistakes

Setting BPDU protection without edge ports. The feature acts on edge ports, so mark host ports as edge first.

Putting no-root-port on an uplink toward the real root. The port then refuses the legitimate root's BPDUs and is blocked.

Waiting for a BPDU blocked port to heal. Without a disable-timeout, the port stays down until you re-enable it.

Confusing loop protection with root protection. Loop protection reacts to missing BPDUs, root protection reacts to better BPDUs.

What to remember for the exam

  • BPDU protection: edge ports that receive a BPDU are disabled; bpdu-block-on-edge.
  • disable-timeout under protocols layer2-control bpdu-block brings the port back automatically.
  • Root protection: no-root-port; superior BPDU leaves the port in a root inconsistent state, and it recovers by itself.
  • Loop protection: bpdu-timeout-action block on the interface under protocols rstp; lost BPDUs leave the port in a loop inconsistent state.
  • BPDU protection is for host ports, root protection for ports facing outsiders, loop protection for ports toward the core.
  • A host sending BPDUs on an edge port is the standard exam scenario for BPDU protection.
  • show spanning-tree interface shows the state of a protected port.

Check yourself

  • A user plugs a small switch into a port configured as an edge port with BPDU protection. What happens?

    The port receives a BPDU and is disabled until it is re-enabled or the disable timeout ends.

  • Which feature stops a customer facing port from ever becoming the root port?

    Root protection, configured with no-root-port.

  • What does loop protection do when a root port stops receiving BPDUs?

    It blocks the port in a loop inconsistent state instead of letting it go to forwarding, and the port recovers when BPDUs return.

Topic 1 of 4 in Layer 2 Security

Test yourself on Layer 2 Security

The full Juniper JNCIS-ENT JN0-352 question bank has 846 questions, with timed practice exams and an explanation for every answer.

This study guide is independent and is not affiliated with, endorsed by, or sponsored by Juniper. Vendor names, certification names and exam codes are trademarks of their respective owners and are used for identification only.