IP Telephony Features · Topic 1 of 2
IP Telephony Features and Power over Ethernet
JN0-650 study page on what an IP telephony deployment needs from a Junos switch and on PoE: standards, power classes, priority, guard band and show poe.
- 5 min
- 802.3af up to 15.4 W, 802.3at (PoE+) up to 30 W, 802.3bt up to 60 W or 90 W at the port.
- The switch is the PSE and the phone is the PD; detection and classification come before power.
- Classes: 0 is 15.4 W, 1 is 4 W, 2 is 7 W, 3 is 15.4 W, 4 is 30 W.
What it is
Voice over IP puts phone calls on the same Ethernet network as data. Calls are sensitive to delay and loss, and phones are usually powered over the network cable. A switch for IP telephony therefore needs more than ports and VLANs.
Power over Ethernet (PoE) sends DC power to a device over the same twisted pair cable that carries data. The switch is the power sourcing equipment (PSE), and the phone is the powered device (PD).
How it works
What a voice deployment needs
| Need | Junos feature |
|---|---|
| Power to the phone | PoE |
| Discovery of settings by the phone | LLDP and LLDP-MED |
| Separate VLAN for voice | Voice VLAN |
| Priority for voice traffic | Class of service |
| Access control for phones and PCs | 802.1X or MAC RADIUS with supplicant multiple |
| Fast convergence | Rapid spanning tree, edge ports |
These features are covered one by one in this guide. This page focuses on power.
PoE standards
| Standard | Name | Power at the switch port | Power at the device |
|---|---|---|---|
| IEEE 802.3af | PoE | Up to 15.4 W | Up to 12.95 W |
| IEEE 802.3at | PoE+ | Up to 30 W | Up to 25.5 W |
| IEEE 802.3bt | PoE++ (4-pair) | Up to 60 W or 90 W | Less, after cable loss |
The device always receives less than the switch sends, because of cable loss. When you size a budget, use the power at the switch port.
Detection and classification
The switch first detects whether a powered device is present by applying a small voltage and looking for the signature of a PD. It then classifies the device to learn how much power it needs, and only then supplies full power.
| Class | Maximum power at the port |
|---|---|
| 0 | 15.4 W (default when no class is signaled) |
| 1 | 4.0 W |
| 2 | 7.0 W |
| 3 | 15.4 W |
| 4 | 30 W (802.3at) |
A device that is not a valid PD gets no power. This is why a PC plugged into a PoE port is safe.
The power budget
A switch has a limited total PoE budget. When the sum of the demands exceeds it, the switch has to refuse power to some ports. Two settings shape the result.
| Setting | Meaning |
|---|---|
priority high or low | Ports with high priority get power first, and low priority ports are cut first when the budget is exceeded |
maximum-power watts | Caps the power for one port |
guard-band watts | Reserves some budget as a margin for peaks |
management class or static | Allocates by the detected class, or by a fixed maximum per port |
set poe interface ge-0/0/1 priority high
set poe interface ge-0/0/1 maximum-power 15
set poe interface all
set poe guard-band 10
set poe management class
With class based management the switch reserves what each device's class allows. With static management it reserves the configured maximum-power for each port, whether or not the device needs it.
If the budget runs out, new devices on low priority ports are denied power. A phone that does not boot after a mass restart is a typical sign.
Verification
show poe interface
show poe interface ge-0/0/1
show poe controller
show poe interface lists the status, class, power in use and priority per port. show poe controller shows the total budget, the power consumed and the guard band, which tells you whether the switch is out of budget. A port can be disabled with set poe interface ge-0/0/1 disable.
| Symptom | Likely cause |
|---|---|
| No power to a phone | PoE disabled on the port, budget exhausted, or a bad cable |
| Phone reboots under load | Class too low for its needs, or maximum-power set too low |
| High priority port loses power | Rare; check the controller state and that the port is not disabled |
| Some phones fail after a restart | Budget not enough for all of them; low priority ports are denied |
Common mistakes
Sizing the budget by the device's power. Use the power at the switch port.
Setting maximum-power below the class. The device cannot get what it needs.
Forgetting to give important phones high priority. They are cut first when the budget is short.
Assuming PoE is only for phones. Access points and cameras use it too.
Expecting power without a valid PD. Detection comes first.
What to remember for the exam
- 802.3af up to 15.4 W, 802.3at (PoE+) up to 30 W, 802.3bt up to 60 W or 90 W at the port.
- The switch is the PSE and the phone is the PD; detection and classification come before power.
- Classes: 0 is 15.4 W, 1 is 4 W, 2 is 7 W, 3 is 15.4 W, 4 is 30 W.
- Priority decides which ports keep power when the budget is short; the guard band keeps a margin.
show poe interfaceandshow poe controllerverify power.- A voice deployment also needs LLDP-MED, a voice VLAN and CoS.
Check yourself
Which PoE standard provides up to 30 W at the switch port?
IEEE 802.3at, also called PoE+.
What happens first when a device is connected to a PoE port?
The switch detects a valid powered device, then classifies it, and only then applies full power.
How do you make sure certain phones keep power when the budget is short?
Set
priority highon their ports.
Topic 1 of 2 in IP Telephony Features
Test yourself on IP Telephony Features
The full Juniper JNCIP-ENT JN0-650 question bank has 858 questions, with timed practice exams and an explanation for every answer.
This study guide is independent and is not affiliated with, endorsed by, or sponsored by Juniper. Vendor names, certification names and exam codes are trademarks of their respective owners and are used for identification only.