Marvis Virtual Network Assistant · Topic 1 of 3
Marvis Actions at Organization and Site Level
Learn Marvis Actions in Juniper Mist: the categories, statuses, AI Validated resolution, driver assist and self driving actions, and org and site views.
- 6 min
- Menu path: Marvis > Marvis Actions; levels are MSP, organization and site.
- Categories: Clients, Layer 1, Connectivity, Wireless, Wired, WAN, Data Center/Application, Security.
- Bad Cable is Layer 1; DHCP, DNS, ARP and authentication failures are Connectivity; Missing VLAN appears under Wired.
What it is
Marvis Actions is the dashboard where Marvis lists the high impact network issues it has detected, together with a recommended action for each one. It covers the wireless, wired and WAN networks and works at the MSP, organization and site levels.
You open it from the left menu with Marvis > Marvis Actions. Juniper describes it as a one stop information center: instead of hunting through events and SLE charts, the administrator starts from a short list of problems that Marvis has already found and explained.
How it works
Categories
Actions are grouped into eight categories across the top of the dashboard: Clients, Layer 1, Connectivity, Wireless, Wired, WAN, Data Center/Application and Security. Clicking a category shows the actions inside it.
| Category | Example actions |
|---|---|
| Layer 1 | Bad Cable |
| Connectivity | Authentication Failure, DHCP Failure, ARP Failure, DNS Failure |
| Wireless | Offline, Health Check Failed, Non-compliant, Coverage Hole, Insufficient Capacity, AP Loop Detected |
| Wired | Missing VLAN, Negotiation Incomplete, MTU Mismatch, Loop Detected, Network Port Flap, Port Stuck, Switch Offline |
| WAN | Bad WAN Uplink, Intermittent WAN Connectivity, VPN Path Down, MTU Mismatch, Non-compliant |
Which actions you see depends on your subscriptions. Wireless actions need Marvis for Wireless, wired actions such as Port Stuck or Loop Detected need Marvis for Wired, and WAN actions need Marvis for WAN. A trial subscription opens all actions for the length of the trial.
Organization and site views
The organization view rolls up every site, and selecting a site shows only its actions, in the same layout.
The categories section always shows only issues that are currently open, whatever time range you pick. The time series graph and the Recommended Actions section show issues in every status for the selected duration. Authentication failures from one authentication server across several WLANs or sites can be grouped into a single organization level action, also visible at site level.
Statuses
Each issue in the Recommended Actions list carries a status, and the list can be filtered by status. By default it shows Open issues for the selected action and duration.
| Status | Meaning |
|---|---|
| Open | The issue is not resolved |
| In progress | Someone is fixing it manually; Marvis is watching |
| Resolved by User | An administrator marked it fixed (driver assist actions only) |
| Marvis Self Driven | Marvis fixed it automatically and is waiting to validate |
| AI Validated | Marvis has confirmed the issue is gone |
Validated resolution
When a user marks an issue Resolved by User, Marvis checks the fix and then moves it to AI Validated. If someone fixes the problem without touching the status, Marvis notices the issue has gone and changes it to AI Validated anyway.
For self driven fixes, the status becomes AI Validated only after Marvis confirms the issue has not come back. If it reoccurs, the status returns to Open.
Driver assist and self driving
| Driver assist | Self driving | |
|---|---|---|
| Who fixes it | The administrator | Marvis, automatically |
| Permission | None needed | Must be granted first |
| Example | Bad Cable: replace the cable | Port Stuck: Marvis bounces the switch port |
Only some actions can self drive:
| Device | Self driving actions | What Marvis does |
|---|---|---|
| APs | Non-compliant | Upgrades AP firmware, one AP per 24 hour window, at low site usage |
| APs | Dynamic Capacity Optimization | Adjusts band and channel width for capacity and interference |
| APs | DFS Optimization | Gives seven day visibility into how RRM handles radar events |
| Switches | Port Stuck | Bounces the port, up to three tries, then sets the issue to Open |
| Switches | Rogue DHCP Server Detected | Disables the access port where the rogue server sits |
| Switches | Missing VLAN | Adds the missing VLAN to the switch port |
| Switches | Loop Detected | Disables the port with the loop; an admin must re-enable it |
| WAN edges | Non-compliant | Updates the backup partition to match the primary |
| WAN edges | Intermittent WAN Connectivity | Bounces the uplink port up to three times |
Permissions are given with the Marvis Self Driven button on the Marvis Actions page, at organization or site level. Organization settings apply to all sites, and site settings override them. Self driving is off by default except for Port Stuck, Intermittent WAN Connectivity and DFS Optimization, which are on by default; DFS Optimization cannot be turned off. A single action can also be switched with its own toggle in Recommended Actions.
Time windows and details
Latest updates covers issues resolved in the last seven days; the graph defaults to 30 days. Issues can be downloaded as CSV, and View More in the Details column shows extra detail, such as the ports missing a VLAN.
Who can see it
Super users can view Marvis Actions. Users with other roles can view it only when they are not limited to specific sites.
Common mistakes
Thinking the category counts follow the time picker. The categories show only issues that are open now. The graph and Recommended Actions follow the selected duration.
Treating Resolved by User as final. Marvis still validates the fix. Only AI Validated means Marvis has confirmed it.
Assuming every action can self drive. Bad Cable, for example, needs a person to replace hardware. Only the listed actions can be fixed automatically.
A self driving fix that does not hold goes back to Open. Do not assume Marvis Self Driven means the problem is solved for good.
What to remember for the exam
- Menu path: Marvis > Marvis Actions; levels are MSP, organization and site.
- Categories: Clients, Layer 1, Connectivity, Wireless, Wired, WAN, Data Center/Application, Security.
- Bad Cable is Layer 1; DHCP, DNS, ARP and authentication failures are Connectivity; Missing VLAN appears under Wired.
- Statuses: Open, In progress, Resolved by User, Marvis Self Driven, AI Validated.
- Driver assist needs a person; self driving needs permission, set at org or site level, with site overriding org.
- Port Stuck, Intermittent WAN Connectivity and DFS Optimization self drive by default.
- Visible actions depend on Marvis for Wireless, Wired and WAN subscriptions.
Check yourself
An administrator replaces a faulty cable and sets the Bad Cable action to Resolved by User. What happens next?
Marvis checks that the issue has gone and then changes the status to AI Validated.
Self driving for Missing VLAN is enabled at organization level but disabled for one site. What happens at that site?
Site level settings override organization settings, so Marvis does not fix Missing VLAN automatically at that site.
An administrator picks a 7 day range but the category counts do not change. Why?
The categories section always shows only currently open issues, regardless of the time range selected.
Topic 1 of 3 in Marvis Virtual Network Assistant
Test yourself on Marvis Virtual Network Assistant
The full Juniper JNCIA-MistAI JN0-253 question bank has 668 questions, with timed practice exams and an explanation for every answer.
This study guide is independent and is not affiliated with, endorsed by, or sponsored by Juniper. Vendor names, certification names and exam codes are trademarks of their respective owners and are used for identification only.