Network Infrastructure and Connectivity · Topic 7 of 9

Wireless Principles

Understand Wi-Fi principles for the CCNA: 2.4, 5 and 6 GHz bands, channel selection, RF terms like dBm and SNR, WPA2 and WPA3 security, and interference.

  • 6 min
In a nutshell
  • SSID is the name. BSSID is the AP radio's MAC address. An ESS joins APs under one SSID.
  • 2.4 GHz has longer range and fewer channels. 5 and 6 GHz have more channels and shorter range.
  • The non-overlapping 2.4 GHz channels are 1, 6 and 11.

What it is

A wireless LAN uses radio waves instead of cables to carry frames between clients and an access point. The standards are the IEEE 802.11 family, sold as Wi-Fi.

Radio is a shared medium. Every device in range on a channel competes for the same airtime, and neighboring networks can interfere.

Good wireless comes from four decisions: which band, which channel, how strong the signal is, and how the traffic is secured.

How it works

A wireless network is a set of names, bands, channels and signal measurements, with encryption on top.

Clientlaptopradio, 2.4, 5 or 6 GHzAccess pointBSSIDwiredSwitchRest of the network

Names

  • SSID: the human readable network name.
  • BSS: one access point and its clients. The BSSID is the AP radio's MAC address, unique to that radio.
  • ESS: several APs sharing one SSID over a wired network, so clients can roam.

Band selection

BandStrengthsWeaknesses
2.4 GHzLonger range, passes through walls betterOnly three non-overlapping channels, crowded, many non-Wi-Fi interferers
5 GHzMany more channels, less crowded, higher speedsShorter range, weaker through walls
6 GHzMany wide channels, almost no legacy devicesShortest range, needs Wi-Fi 6E or Wi-Fi 7 clients
StandardMarketing nameBands
802.11nWi-Fi 42.4 and 5 GHz
802.11acWi-Fi 55 GHz
802.11axWi-Fi 6 (6E adds 6 GHz)2.4 and 5 GHz, plus 6 GHz in 6E
802.11beWi-Fi 72.4, 5 and 6 GHz

A dual band client picks the band. Putting latency sensitive clients on 5 GHz or 6 GHz leaves the crowded 2.4 GHz band to devices that can use nothing else.

Channel selection

In 2.4 GHz, channels are 5 MHz apart but about 20 MHz wide, so neighboring channels overlap. The only non-overlapping set is 1, 6 and 11.

AP 1channel 1next toAP 2channel 6next toAP 3channel 11next toAP 4channel 1 again

Neighboring APs should use different channels from this set, and APs that hear each other should avoid sharing one.

In 5 GHz there are many more non-overlapping 20 MHz channels. Some of them are shared with radar, and rules require the AP to move off a channel when it detects radar (DFS).

Wider channels (40, 80 and 160 MHz) carry more data but use more spectrum and leave fewer non-overlapping channels. In a crowded area, 20 MHz channels give a more stable result.

Exam tip

In 2.4 GHz, think 1, 6 and 11. Any other set of neighboring channels overlaps.

RF characteristics

  • Frequency: cycles per second, in hertz. Higher frequencies carry more data but cover less distance and penetrate less.
  • Signal strength: measured in dBm, a logarithmic scale. A value nearer to zero is stronger, so minus 50 dBm is much stronger than minus 80 dBm.
  • Noise floor and SNR: noise is unwanted energy on the channel. SNR compares signal to noise, and a higher number means a cleaner link. Design guides often aim for a signal around minus 67 dBm or better and an SNR above about 25 dB.
  • Attenuation: loss of signal with distance and when passing through walls, glass, metal and people.
  • Reflection and multipath: signals bounce off surfaces, so the receiver gets several delayed copies of one signal.
  • Antenna gain and EIRP: an antenna focuses energy in a direction. EIRP is the effective radiated power: transmitter power, minus cable loss, plus antenna gain.

As signal falls or noise rises, clients drop to slower data rates to keep the link, so throughput falls long before the connection is lost.

Causes of interference

CauseDetail
Co-channel interferenceNearby APs on the same channel share airtime
Adjacent channel interferenceOverlapping channels, such as 2.4 GHz channels 1 and 3, corrupt each other
Non-Wi-Fi devicesMicrowave ovens, cordless phones, Bluetooth and wireless video devices on 2.4 GHz
RadarWeather and other radar in some 5 GHz channels
Physical obstaclesMetal, concrete, water and glass absorb or reflect signal

Co-channel sharing is polite but slow. Adjacent channel interference is worse, because the devices cannot hear each other and just corrupt frames.

Security protocols

Radio can be received by anyone nearby, so wireless traffic is encrypted and users are authenticated.

ProtocolEncryptionKey methodStatus
WEPRC4Static keyBroken, never use
WPATKIPPSKObsolete
WPA2AES with CCMPPSK or 802.1XWidely used
WPA3AES with CCMP or GCMPSAE or 802.1XCurrent best

Each comes in two modes. Personal uses one shared passphrase, the pre-shared key. Enterprise uses 802.1X and a RADIUS server, so each user authenticates individually and gets unique session keys.

WPA3-Personal replaces the PSK handshake with SAE, which blocks offline guessing of the passphrase. WPA3 also requires protected management frames, which stop forged disconnect messages. 6 GHz networks require WPA3 (or Enhanced Open).

Watch out

dBm values are negative. Minus 90 dBm is far weaker than minus 50 dBm.

Common mistakes

Choosing channels 1, 2 and 3 in 2.4 GHz. They overlap. Use 1, 6 and 11.

Confusing SSID and BSSID. Many radios can share one SSID, but each BSSID is unique.

Reading dBm backwards. A smaller negative number is a stronger signal.

Assuming more power always helps. A strong AP can be heard by a client that the AP cannot hear back.

Treating a hidden SSID as security. It neither authenticates nor encrypts.

What to remember for the exam

  • SSID is the name. BSSID is the AP radio's MAC address. An ESS joins APs under one SSID.
  • 2.4 GHz has longer range and fewer channels. 5 and 6 GHz have more channels and shorter range.
  • The non-overlapping 2.4 GHz channels are 1, 6 and 11.
  • Signal strength is in dBm, and the number nearer to zero is stronger. Higher SNR is better.
  • Causes of interference: co-channel, adjacent channel, non-Wi-Fi devices, radar and obstacles.
  • WEP is broken. WPA2 uses AES-CCMP. WPA3 adds SAE and protected management frames.
  • Personal uses a shared passphrase. Enterprise uses 802.1X and RADIUS.
  • Wider channels give more speed but fewer clear channels.

Check yourself

  • Why are only channels 1, 6 and 11 used together in 2.4 GHz?

    Channels are 5 MHz apart but about 20 MHz wide, so neighboring channels overlap. Only 1, 6 and 11 do not.

  • Name three causes of wireless interference.

    Co-channel interference from APs on the same channel, non-Wi-Fi devices such as microwave ovens and Bluetooth on 2.4 GHz, and radar in some 5 GHz channels.

  • What does WPA3-Personal change compared with WPA2-Personal?

    It replaces the PSK handshake with SAE, which blocks offline guessing of the passphrase, and it requires protected management frames.

Topic 7 of 9 in Network Infrastructure and Connectivity

Test yourself on Network Infrastructure and Connectivity

The full Cisco CCNA 200-301 v2.0 question bank has 1,242 questions, with timed practice exams and an explanation for every answer.

This study guide is independent and is not affiliated with, endorsed by, or sponsored by Cisco. Vendor names, certification names and exam codes are trademarks of their respective owners and are used for identification only.